Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Mayfair Homeowners
A missing or cracked chimney cap is the small opening that lets a large problem into your house. Rain runs straight down the flue, squirrels and birds nest in the smoke chamber, and within a season or two you’re looking at a rusted damper and water-stained ceiling plaster above the firebox. Mayfair’s older brick rowhouses and twin homes take this hard, because a lot of them were built with simple mortar crowns and no cap at all. We install and repair caps and crowns as part of a full-system chimney service, using Gelco and Famco caps and HeatShield crown coatings rather than whatever is on the shelf at a hardware store. Our technicians have up to 9 years of experience. Call (888) 841-6695 for a free estimate, and we’ll book your sweep and cap assessment together.
What Our Chimney Cap & Crown Service Includes
Cap Installation
A chimney cap is the hooded cover that sits on top of the flue, screening out rain, snow, animals, and debris while letting smoke escape. If your flue is open to the sky, you need one – the cost of a cap is a fraction of what a water-damaged damper or a bird nest removal will run. We size Gelco and Famco caps to the exact inside dimensions of your flue, not the nearest catalog size, so the fit is tight and the mounting is secure against wind.

Cap Replacement
Caps fail in stages. The screen rusts through, the mounting legs loosen, or a storm knocks the whole assembly off the crown. A loose cap that rattles or sits crooked is no longer protecting the flue, and a missing cap lets water straight in. When we replace a cap in Mayfair, we inspect the crown underneath while we’re up there – replacing the cap without checking the crown is half a repair.

Crown Repair
The crown is the concrete or mortar slab at the very top of the chimney that slopes water away from the flue. When it cracks, spalls, or pulls away from the flue tile, water seeps into the masonry below and freeze-thaw cycles widen the damage year after year. We repair crowns with proper bonding and forming techniques, rebuilding the slope so water runs off the way it’s supposed to. Small cracks caught early are a straightforward fix; a crown that’s crumbling to the touch is a rebuild.

Crown Coating
Crown coating is a protective membrane applied over a sound but aging crown to seal hairline cracks and stop water intrusion before it spreads into the brickwork. It’s the right call when the crown is structurally intact but showing surface wear – a coating adds years of service without tearing the crown apart. HeatShield crown coating products are what we specify here: they flex with the masonry, resist UV, and form a durable barrier against the freeze-thaw damage that shortens the life of Mayfair’s older chimneys.
Multi-Flue Cap
Many Mayfair homes have chimneys with two or more flues side by side – one for the fireplace, one for a furnace or water heater. A multi-flue cap covers all of them in a single unit, keeping each flue individually screened while sharing one stable mounting across the crown. It’s a cleaner look and a stronger install than fitting separate caps to each flue. We measure the entire flue arrangement and specify a Gelco or Famco unit sized to fit.
Custom Cap
Oversized flues, odd chimney shapes, and non-standard crown dimensions don’t fit a stock cap. We spec custom caps through our Olympia Chimney and Gelco supply channels when the flue is bigger than standard, sits off-center, or needs a specific finish to match the house. A custom cap is a precise fit, which is what keeps wind and water out over the long haul.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We specify Gelco and Famco caps because both are built for the job, not adapted from generic sheet metal. Gelco caps are known in the trade for precision fit and strong weather performance, and Famco units hold up well where wind exposure is a real concern. We size them to the actual flue dimensions, which matters more than the brand name on the box.
For crown work, HeatShield coatings are what we reach for when a crown needs protection without a full rebuild. On the supply side, we source through Olympia Chimney and Copperfield, the same wholesale chains professional chimney contractors rely on, so we’re not limited to what a big-box store carries. Whether you have a Gelco cap that’s outlived its screen or a crown that’s never had any coating at all, or any other make, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Water in the firebox after rain. If you’re finding moisture, rust stains, or a damp smell after a storm, the cap or crown isn’t shedding water. Left alone, moisture reaches the damper, the smoke chamber, and eventually the ceiling below the chimney.
- A cracked, spalling, or crumbling crown. Crumbling mortar at the top of the chimney means water is getting into the masonry. Freeze-thaw cycles in this region accelerate the damage, so a crown that’s failing now gets worse through winter.
- Animals or nesting debris in the flue. Birds, squirrels, and raccoons get into open flues easily. A proper cap with a screen stops that, and it also removes a serious obstruction risk before the next fire.
- A missing, loose, or rusted-through cap. A cap that rattles in wind or has lost its screen is doing nothing. Replacing it protects the flue and the crown and stops larger repairs from forming.
- Draft problems or smoke rolling back into the room. Sometimes an oversized or poorly fitted cap doesn’t pull properly with the flue. A correctly sized cap, matched to your flue’s dimensions and the chimney’s location, fixes smoke spillage that no amount of firewood adjustment will solve.
Our Chimney Cap & Crown Process – Step by Step
- 1
Assessment from the ground and up top. We start with a look at the chimney from grade, noting the crown’s condition and the cap’s placement, then work from a stable ladder or roof surface to inspect directly. We check the flue tiles, the crown’s slope and surface, and the cap’s mounting points.
- 2
Photos and a written estimate. You see what we see. We photograph the crown, the flue opening, and any existing cap before recommending anything, and the written estimate breaks out the work line by line so you can compare it to what the photos show.
- 3
Cap sizing and specification. For caps, we measure the flue’s inside dimensions and specify the right Gelco or Famco unit – screen size, mounting style, and finish. Custom sizes go through our Olympia Chimney and Gelco supply channels.
- 4
Crown preparation and application. Crown repairs and coatings start with surface preparation – cleaning and removing loose material, addressing cracks, and forming the proper slope. HeatShield coating is applied to the prepared surface, and repairs are built to shed water, not just fill a gap.
- 5
Final check and walkthrough. We verify the cap seats firmly with no gaps at the flue, confirm the crown drains away from the flue tile, and walk you through the photos of the finished work. You get the estimate, the photos, and the reasoning before anything else.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Mayfair?
A chimney cap and crown job in Mayfair typically runs from a few hundred dollars to well over a thousand, depending on what’s actually needed. A standard-sized cap installed over a single flue usually lands in the lower half of that range. A multi-flue cap or a custom-sized unit costs more because the material and spec work are larger. Crown work – coating or repair – is priced by the condition and accessible area of the crown; a full rebuild is the top of the range.
What drives the price: flue size and number of flues, whether the crown is intact or needs rebuilding, cap style and material, chimney height and access, and whether the work is bundled with a sweep or liner repair at the same visit. Bundling saves you a second visit.
A free estimate means a written price before any work begins, with photos of what we found. Nothing gets recommended that the camera evidence doesn’t show you can see yourself. Every price we quote is an estimate – the written estimate sets the final number, not a phone guess.
Chimney Cap & Crown Near Mayfair – Our Service Area
We work across Mayfair and the surrounding neighborhoods, including chimney cap & crown work in University City to the south and chimney cap & crown in Point Breeze to the southwest. We also serve Wyndmoor, Flourtown, Cheltenham Village, Tacony, Holmesburg, Cornwells Heights, Bala Cynwyd, Springfield, and Center City. Response times depend on location and the day’s schedule. If you’re outside these areas, call and we’ll tell you straight whether we cover your block.
Serving Mayfair, PA – Our Local Coverage Area
We serve Mayfair and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Mayfair
A chimney cap is the hooded cover at the top of the flue that keeps rain, animals, and debris out; the crown is the sloped slab of concrete at the very top that sheds water away from the masonry. Both protect the flue and the brickwork below from water damage. When either one fails, water gets into the chimney body and starts breaking down the liner, damper, and surrounding structure. Call (888) 841-6695 for an inspection – estimates are free.
Most cap replacements and crown coatings are completed in a few hours, while a full crown rebuild or a multi-flue cap installation can take longer depending on access and chimney height. We give you a time estimate in the written estimate so you can plan around it. The work isn’t rushed; a crown needs proper curing and a cap needs proper seating. Call (888) 841-6695 for an estimate.
Cap installation generally starts in the low hundreds and runs up from there depending on flue size and cap type, while crown repair and coating are priced by the crown’s condition. A full crown rebuild is the most expensive of the options. The written estimate sets the final price, and nothing is added afterward. Call (888) 841-6695 – estimates are free.
Yes – we specify and install Gelco and Famco caps and source through Olympia Chimney and Copperfield’s professional supply chains. We also replace or repair existing caps of other makes. If the cap is the wrong size for the flue or has failed at the mounting, we’ll tell you what needs to change. Call (888) 841-6695 for an exact quote.
Same-day service is available when the schedule allows. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday; we’re closed Saturday. A call outside dispatch hours is booked into the next opening. Call (888) 841-6695 to book.
We stand behind the installation, and any warranty details are spelled out in the written estimate before work begins. Cap installation and crown repair are backed as described in that document. If you have questions after the job, call and ask – we’ll walk you through what was done and what the coverage says. Call (888) 841-6695.
Clear a path to the fireplace and the chimney access point, and make sure the area inside the house is free of breakables. We handle everything above the roofline and around the crown. If you have a gas appliance connected to a flue, let us know when you book so we can plan the inspection around it. Call (888) 841-6695 to schedule.
Schedule Your Chimney Cap & Crown Service in Mayfair Today
One call covers the whole chimney envelope – sweep, cap, crown, liner, and fireplace – so you’re not coordinating two contractors for one chimney. We answer 24/7, fast dispatch from 7am to 7pm, Sunday through Friday. Call (888) 841-6695 for a no-obligation free estimate. Photos, written price, and a clear explanation of what’s actually needed before any work starts.
Written by the team at Chimney Sweep Mayfair.