Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Liner & Rebuild for Mayfair Homeowners
If your fireplace smells like smoke when it isn’t burning, or a sweep has told you the flue is cracked, the liner is the piece of your chimney you can’t see and can’t afford to ignore. Mayfair’s older rowhouses and postwar homes often have clay tile flues that have cracked, spalled, and pulled apart at the joints after decades of heating cycles. A stainless steel liner restores a continuous, sealed path for smoke and gases from the firebox to the top of the crown, and a rebuild addresses what happens when the masonry around that flue has deteriorated too far to hold a liner safely. Our technicians have up to 9 years of experience with full-system chimney work, and we scope the job by camera before we quote it. Call (888) 841-6695. We answer 24/7. Fast dispatch from 7am to 7pm.
What Our Chimney Liner & Rebuild Service Includes
A chimney is a system, not a tube. The flue, firebox, smoke chamber, crown, and cap all have to work together or the whole thing drafts poorly and fails early. That’s why we handle the liner and the rebuild as one scope rather than handing pieces of the job to separate contractors.
Stainless Steel Liner
A stainless steel liner is a rigid or semi-rigid pipe that runs the full length of your flue, giving smoke and carbon monoxide a sealed path out of the house instead of letting them work into cracked clay tile and surrounding masonry. You need one when the existing clay flue has cracks, gaps at the joints, or an improper size for the appliance you’re venting. We install DuraFlex flexible stainless systems, the professional-grade standard contractors specify for relining, insulated to code and sized to the appliance so draft is right and creosote doesn’t build faster than it should.
Flexible Liner
A flexible liner is the right answer for a chimney with offsets, bends, or an irregular flue path where rigid pipe won’t pass cleanly. It’s also the usual choice for a clay flue that’s cracked but structurally intact, since the flexible stainless can be pulled through and then insulated in place. We measure the flue and confirm clearances before we specify a liner, so the flexible system you get is sized for your firebox and appliance, not pulled off a shelf by guesswork.
Liner Replacement
Liner replacement is the job when a previous liner has failed, was undersized from the start, or was installed without insulation and now shows corrosion or joint separation. You’ll usually know because draft has gotten worse, the fire is harder to light, or a sweep found debris falling from above. We pull the old liner, inspect the flue walls, and install a replacement sized to your appliance with the correct clearances and insulation rather than matching what was there before.
Partial Rebuild
A partial rebuild is masonry repair limited to the section that has failed, most often the top few courses above the roofline where freeze-thaw cycles do the most damage to the crown and uppermost brick. You need it when the crown is spalling badly, brick faces are flaking off, or water is getting behind the masonry and showing up inside. We rebuild the failed section, tie it back into sound masonry, and reset a properly sized cap so the repair holds through the next few winters.
Full Chimney Rebuild
A full rebuild is warranted when the chimney stack is leaning, the mortar joints are failing throughout, or the flue can no longer safely hold a liner. Rebuilding an entire chimney is not a small job, and it’s one where the estimate should explain exactly what is coming down and what is going back up. We tear out the failed masonry, rebuild the stack and flue, and finish with a new crown and cap so the rebuilt chimney is complete rather than waiting on a second contractor.
Liner Repair
Liner repair covers the cases where the liner itself is intact but a joint, connection, or transition has failed: a separated section at the top plate, a bad connection at the appliance, or a gap at the smoke chamber. These are the leaks that let creosote collect behind the liner and let smoke back into the room. We use HeatShield to resurface and seal deteriorating fireboxes and flue joints in qualifying systems, which can restore a sound chimney without tearing out a liner that still has service life.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Liner & Rebuild
We install and work with DuraFlex flexible stainless steel relining systems because they’re what professional installers specify when a flue needs a sealed, insulated path from the firebox to the crown. When a firebox or flue joint needs resurfacing rather than replacement, we use the HeatShield restoration system, which lets us seal a deteriorating smoke chamber or firebox face in qualifying systems instead of recommending a full tear-out. We also specify Gelco and Famco chimney caps and covers, chosen for precision fit and weather performance rather than generic off-the-shelf hardware.
Our supply comes through Olympia Chimney and Copperfield, the same wholesale channels professional chimney contractors rely on, not big-box substitutes. That matters for a liner, because the wall thickness and grade of the stainless steel determine how long it lasts in a working chimney. Whether your existing setup involves DuraFlex, HeatShield, Gelco, Olympia Chimney, or another make entirely, we can help.
Signs You Need Chimney Liner & Rebuild Right Now
- Smoke spilling into the room when you light a fire. Poor draft often means the liner is cracked or undersized, letting gases escape into the chase instead of up and out. It’s a sign to stop burning and get the flue inspected before your next fire.
- Mortar and tile fragments in the firebox. Pieces of clay flue tile falling into the box mean the flue lining is failing from the inside. A cracked flue lets heat reach surrounding wood framing, so this one is worth checking quickly.
- A strong smoky or creosote smell when the fireplace is off. Odors drifting back into the house point to a leaky liner joint or a draft reversal that a liner and cap work together to fix. It gets worse in damp weather and when the pressure in the house changes.
- Visible spalling on the crown or upper brick. Flaking brick faces and a crumbling crown let water into the masonry, and a wet chimney breaks down faster in cold weather. A partial rebuild with a properly fitted Gelco or Famco cap stops the cycle before it reaches the lower stack.
- Water staining on the ceiling near the chimney. Staining usually traces back to a failed crown, missing cap, or failed flashing at the roofline. Water inside the chase rusts the liner and weakens the masonry, so it’s worth finding the source before more damage happens.
Our Chimney Liner & Rebuild Process – Step by Step
- 1
Camera inspection of the full flue. We run a camera down the length of the flue and look for cracks, gaps at the joints, offsets, and debris. This is the step that decides whether you need a liner repair, a replacement liner, or masonry work above the roofline.
- 2
A written scope and a flat estimate. We write out what’s failing, what we recommend, and the price for the work before anything is booked. If part of the job can safely wait, we say so, so you’re not paying for work the chimney doesn’t need yet.
- 3
Prep the flue and protect the home. We clear the flue, set up containment at the firebox and the roof, and lay drop cloths along the path. Chimney work is dusty, and keeping the interior clean is part of a professional install.
- 4
Install the liner or rebuild the stack. For a liner, the stainless system is sized to your appliance and insulated in place. For a rebuild, the failed masonry comes down, the flue and stack go back up, and we finish with a new crown and cap sized to the flue.
- 5
Insulate, seal, and confirm with another camera pass. We seal the top plate, insulate where the job calls for it, and run the camera again to confirm the liner is continuous and the joints are sound. You get photos of what we found and what we installed.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Mayfair?
A typical stainless steel liner installation on a single-flue chimney in Mayfair runs roughly $2,400 to $4,800 depending on the height of the flue, the size of the appliance being vented, and whether insulation and a new top plate are part of the scope. Liner repair, where the liner is sound and only a joint or connection has failed, generally falls in the $300 to $900 range. A partial rebuild of the crown and upper courses typically runs $1,200 to $3,000, and a full chimney rebuild ranges from $6,000 to $14,000 or more depending on how much of the stack has to come down and whether the firebox and smoke chamber need work at the same time.
What moves the price: chimney height, the number of flues, whether the existing liner has to be removed, and whether the crown and cap need to be replaced along with the flue. To avoid overpaying, ask for the square footage of masonry being rebuilt and the liner specs in writing, and ask whether any part of the job can safely wait a season. Our estimates are free and set the final price per job in writing, with camera evidence you can see for yourself before you agree to anything.
| Service | Typical Estimated Range | What Drives the Price |
|---|---|---|
| Liner repair (joint or connection) | $300 – $900 | Access, extent of the failed joint, HeatShield resurfacing needed |
| Stainless steel or flexible liner install | $2,400 – $4,800 | Flue height, appliance size, insulation, top plate |
| Liner replacement (remove and reinstall) | $3,000 – $5,500 | Old liner removal, flue condition, replacement sizing |
| Partial rebuild (crown and upper courses) | $1,200 – $3,000 | Height of failed section, new crown, cap sizing |
| Full chimney rebuild | $6,000 – $14,000+ | Stack height, flue count, firebox and smoke chamber scope |
Chimney Liner & Rebuild Near Mayfair – Our Service Area
We work with homeowners across Mayfair and the surrounding neighborhoods, including University City, Point Breeze, Wynmoor, Center City, Springfield, Flourtown, Bala Cynwyd, Cheltenham Village, Cornwells Heights, Tacony, and Holmesburg. Dispatch runs 7am to 7pm, Sunday through Friday, so booking a sweep for a nearby town is usually straightforward. If your chimney needs the full scope of liner and rebuild work, see our chimney liner & rebuild page for the details, or start with our Chimney Sweep Mayfair service for an inspection.
Serving Mayfair, PA – Our Local Coverage Area
We serve Mayfair and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Liner & Rebuild in Mayfair
Chimney liner and rebuild work covers the inside and outside of the chimney: a stainless steel liner restores a sealed path for smoke and gases through the flue, and a rebuild repairs the masonry that holds that flue. The two are done together when the flue has cracked and the surrounding masonry has also deteriorated. Call (888) 841-6695 for an exact quote – estimates are free.
A stainless steel liner install on a single-flue chimney usually takes a day, and a liner replacement or partial rebuild often runs one to two days, while a full chimney rebuild can take several working days depending on the height and scope. The written estimate sets the realistic timeline once we’ve seen the flue by camera. Call (888) 841-6695 for an exact quote – estimates are free.
A stainless steel liner installation in Mayfair typically runs $2,400 to $4,800, and liner repair generally falls around $300 to $900 depending on the failed joint. Partial rebuilds run $1,200 to $3,000 and full rebuilds $6,000 to $14,000 or more. The written estimate sets the final price per job. Call (888) 841-6695 for an exact quote – estimates are free.
Yes. We install DuraFlex flexible stainless steel liners, apply the HeatShield restoration system on qualifying fireboxes and flue joints, and specify Gelco and Famco caps. We also work with Olympia Chimney and Copperfield supply. Whether your setup involves any of those brands or another make, we can help.
Yes, same-day work is available for liner and rebuild jobs when scheduling allows. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (888) 841-6695 for an exact quote – estimates are free.
Our liner and rebuild work is backed by a satisfaction guarantee, with the terms written into your estimate before anything is booked. If something isn’t right after the job, we come back and make it right. Ask for the warranty language in writing so you know exactly what’s covered.
Clear access to the firebox, remove anything fragile from the hearth, and keep a path from the door to the chimney clear so we can carry equipment through without obstruction. We lay drop cloths and set up containment, so most prep on your end is simply making room. Call (888) 841-6695 if you have questions before the visit.
Schedule Your Chimney Liner & Rebuild Service in Mayfair Today
If your flue has cracks, your crown is spalling, or your fireplace has started smoking back into the room, a camera inspection will tell you exactly what’s failing before you commit to any work. Call (888) 841-6695. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, and estimates are free with the price set in writing per job. One contractor, one chimney, start to finish.
Written by the team at Chimney Sweep Mayfair.